TLF-0.5.2
(C) 2001, 2002 - Rein Couperus, PA0RCT
a free console mode general purpose CW keyer,
logging and contest
program for hamradio
under LINUX
This program is published under GPL

Content
Description
TLF-0.5.2 is a console (ncurses) mode general purpose CW keyer, -logging and -contest
program for hamradio. It supports the CQWW, the WPX, the ARRL-DX , the ARRL-FD,
the PACC and the EU SPRINT contests (single operator)
as well as a lot more basic contests, general QSO and DXpedition mode.
It interfaces with a morse code generator, a number of radios, and with a DX Cluster.
Contest operation mimics the popular TR-Log program for DOS, the output file is TR- as well
as CABRILLO compatible. The user interface was designed with over 30 years of experience in
CW contesting in mind. The program was written for console mode on purpose, to make it run
also on smaller machines, or remotely via a modem link. TLF is developed under Slackware 8.0, and tested under
SuSE 7.0, kernel version 2.2.16, and RH 7.2, with 2.4 kernel.. Beta testers welcome !!!
Two keyer modules are now supported. The cwkeyer from Ivo, 9A3TY with output on either ttyS0 or ttyS1,
and the (more flexible) cwkeyer for the parallel port from Eric, PA3FKN with output on LP0. They both work with a cw output device called /dev/cwkeyer,
and can be fully controlled by TLF.
For the cwkeyer module for COM ports there is a special source file especally for kernels 2.4.x on the website (called cwkeyer.c.k24).
The default file in the distribution of cwkeyer-0.1 only works for k2.2 and below.
The keyer from Eric, PA3FKN works also for kernels 2.4.x without problems.
Why TLF
I have been using mostly TR-Log for contesting, or CT when working as guest op in M/S operations. I am
especially fond of TR-Log. When you have a DOS computer, you don't need TLF. You should use TR-log.
However, I have now removed all WINDOWS and DOS software from my computers and put LINUX on.
This means I can't use my favourite contesting software anymore (yes, I have also experimented with DOSEMU,
but without great success...)
TLF started as a simple keyboard interface to cwkeyer-0.1 from 9A3TY. When the WPX 2001
was 2 months away I had to try to write my own program. That turned out to be great fun. The result of this is TLF,
which very much represents my idea of what a CW contest program should do.
Some have asked what the name stands for. The old hands from the days when CW was still hand-crafted will
certainly know. It means Try Left Foot.
On special request TLF will now also log SSB and DIGIMODE qso's.
Features
Permanent information displays:
Keyer output, last 5 log lines, UTC time, keyer speed, delay, keyer status
(Keyboard|CQ|S&P|Auto), DX database output for active call, or WWV data if available via packet.
Optional information windows:
Screen pic
Dupe check,
score,
raw cluster output | DX spots only | Band Map,
Check partial call with a database of some 28.000 known contest calls,
Zones worked,
Countries worked
Propagation diagrams based on sun spots, qrb, sunup, sundown, qtr, etc.
Keyer:

6 - 60 wpm,
12 CW messages programmable online (you will not remember more anyway..)
Auto-CQ with adjustable delay
Output to the TX on /dev/ttyS0 or /dev/ttyS1 or lp0, using /dev/cwkeyer kernel module.
Sidetone is adjustable (and optional).
TXdelay and weight adjustable
Database:

Uses reformatted cty.dat.
Conversion script is included in the distribution.
Interfaces:
TLF interfaces through the file system:
For CW output it writes to /dev/cwkeyer.
For Cluster input it regularly reads a file called clfile.
Interface to the radios has been kept modular, so others can write interfaces to various types.
The program simply looks into a file QRG for the actual
trx frequency, and writes to a file called QRGOUT to set the trx frequency and reset the RIT control.
Of course you can grab dx spots, do fast qsy etc...
Radios presently supported:
Installation
Install the CW kernel driver
You now have a choice out of two kernel modules, depending whether you want to use output on a COM (serial)
port or on LPT1, the parallel port.
Installation of the parallel port driver
Get Cwkeyer.tgz from the TLF website and get it to work .
Just unzip and untar the file cwkeyer.tgz, go into its directory and make. Start the module with "load",
and stop it with "unload". You have to be root to do this ! (TLF can be run as user).
Key output is on bit 3 and PTT output is on bit 2 of the parrallel port.
Installation of the serial port driver
Get TLFcwkeyer (based on cwkeyer-0.1 from 9A3TY) ( and get it to work (as root).
You need the special version from the TLF website,
because it will allow you to change the cw speed in 2 wpm increments.
Moreover it will allow stopping the message as soon as it has started.
The original module can not do this (yet).
For distributions working with kernel 2.4.x, a modified version of cwkeyer.c is on the TLF website.
The README file in the distribution (TLFcwkeyer.tar.gz)
gives excellent directions for the installation.The TLF distribution contains
a script, startcw to start the module. Edit it first to use the right directory names and output port
(ttyS0 or ttyS1).
If you have problems, first check if all file permissions are o.k.
Output is on the DTR pin of the port.
You can use the same simple hardware
interface as for TR , CT or DX4WIN.
Example of my own startcw script which will start the cw kernel module on ttyS1:
#! /bin/bash
# starts the cw driver
cd /home/rein/cwkeyer-0.1
make cwup2
echo "CW OK" > /dev/cwkeyer
cd /home/rein/TLF-0.2
Install the TLF program.
Get the latest distribution of tlf from the download site (ftp://sharon.esrac.ele.tue.nl/pub/linux/ham/tlf).
tlf now supports GNU autoconf and automake, which automates the installation process, and makes sure you have
all the goodies on your machine which tlf needs..
* Read README and INSTALL
* Unzip the tarball (e.g. gunzip tlf-0.5.2.tar.gz).
* Untar the archive (e.g. tar xvf tlf-0.5.2.tar)
* cd into the top directory (cd tlf-0.5.2)
* type ./configure
* type make (Ignore the 3 warning messages about the 2-digit year.)
* type make install
It is good practise to use separate directories for the different contests.
TLF can be started from any directory. to start a specific contest you need to:
* mkdir contestname
* copy the logcfg.dat file for that specific contest into it (it is located at /usr/local/examples/contestname)
* edit the logcfg.dat file (call, logfile) to suit your needs
* start tlf with tlf
Tlf will put some files into the working directory, viz.: clfile and wwvfile.
For radio control:
- trxcontrol (only for ten tec 563 and icom 735)
You can convert the latest cty.dat file into ctydb.dat if necessary with the script provided
(convertctydb).
The cty.dat file included in the distribution is the one from October 2001.
Edit the filterline script (e.g. change the call).
TLF needs some bash commands to work: system( ), tr, cut, sed, egrep, cp, rm, tail, less, joe.
Preparation
Make sure the CW kernel module cwkeyer.o (as root) runs (try the startcw script)
Start the input (cluster) fifo in the
working directory if you want to use the cluster info (see FILES)
Start the program (tlf).
FILES
. / clfile | This is the input file for the DX cluster
monitor. You only need it when you use a dx cluster, or any other information you want the
program to display. There are several ways to get the cluster
data into it.
You can use the "call" ax25 tool. It has the possibility to write a logfile. This is started with ~o, and is called
logfile.txt. You can get the info into clfile with : tail -f logfile.txt >> clfile
You can also use telnet. Open a new terminal, and start telnet with:
telnet node | tee -a clfile
TLF will pick it up from there (it will look in the working directory for clfile!!).
I sometimes use minicom and a TNC2. To filter out the Escape sequences I use a script
called filterpacket (example included in the distribution). |
. / ctydb.dat | This is the DXCC database. It resides in /usr/local/share/tlf. |
. / .paras | The parameter file. It remembers the
parameters for the next session. TLF will generate one for you.
It is normally not necessary to touch this, as all parameters are included in the file
logcfg.dat, which can be edited within tlf. |
. / logcfg.dat | The configuration file. It enables you to configure tlf for a special contest,
for normal qso operation, etc. All parameters are already in the file. They are enabled by uncommenting them (erase
the # in the first position of the line). You should stick to the format as much as possible. In case certain parameters are mutually
exclusive, the last one wins.... As more functions become available in future, new versions of logcfg.dat will
become available. |
. / wwvfile | Contains the latest wwv info received from the dx cluster |
. / QRG | If this file is present and trx control enabled (parameter :trxcontrol)
, tlf will follow the band switch of the transceiver. (So if you can not change band anymore you now know why :-)). |
. / QRGOUT | This is written by tlf if trxcontrol is enabled, and you tell tlf to qsy by
changing the band, grabbing a spot or just entering the frequency into the call input field. QRGOUT is deleted by
the trxcontrol interface after the qsy has been done.. |
/usr/local/share/tlf/filterline | Script needed by the program. It is used to filter out
clutter from the DX cluster. You can edit it to change the filter. |
xxxxxxxxxxxxxxx.log | The log file |
. / cabrillo | This file will be generated by the ":write" command after
the contest. Rename to YOURCALL.CBR and email.... |
Operation
Logging qso's
Al activity takes place in the call input field (and the exchange input field..).
When you enter (part of) a call, several things happen:
- If check partials is on, and auto_complete is active, the call will be automatically completed. E.g. when you
type PA0RC, it will automatically complete to PA0RCT. The same for KC1X?, W3LP? etc....
- Backspace will remove character from the end of the call
- ESCAPE will remove the call completely
- left_arrow will allow you to edit the call in the input field (enter edit mode)
- As soon as you have entered edit mode (colour of the call field changes )you can overwrite characters in the call field
- In edit mode you can use Delete to delete characters
- To Insert a single character type the Insert key first.
- If after a Delete or an Insert you leave edit mode with TAB, the auto_complete function is switched off for the running qso.
This enables you to change a call when it is locked by auto_complete because it is a unique call in the database
-
- If after a Delete or an Insert you leave edit mode with ESCAPE or ENTER, auto_complete is not switched off.
- If the check window is on, it will show the last qso's in the log (on the contest bands)
- The bottom status line will show country and qrb info, as well as the local time of the station..
- When you press Ctrl-p you will get a screen with the muf curve based on the number of sunspots,
the distance, bearing , sunset, sundown etc. Any key will get you back to where you came from.
- You can go to the exchange field with SPACE or TAB.
- ENTER will log the qso in SSB mode, and also if you are in CW and qso (non-contest) mode.
- In case you want to log a cw qso during a contest without cw output, you can use "\" (backslash).
Deleting qso's
Using the "-" key will delete the last qso from the log (after asking your permission of course).
Editing the previous qso
You can recall the previous qso with "@". Log it without cw output with "\" (backslash)
Changing RST
You can change RST sent when a Call is in the Call Input Field. Page_down will lower the S value and Page_up will increase it.
RST received can be changed by going into the exchange field and using Page_down and Page_up accordingly.
Changing CW/SSB mode
The command is :mode.
Changing Bands
When you are in the call input field, use the left_arrow and right_arrow keys to change the band.
When contest mode is on, only the contest bands can be reached (160-80-40-20-15-10).
If a radio interface is present, band switching can be done in several ways:
- Switch bands on the radio - tlf will follow
- Switch bands on tlf - the radio will follow
- Enter a frequency in tlf - the radio will jump to that qrg
- Pick a frequency from bandmap or spot list - the radio will go there
- If you have a frequency int the MEMory, press # - the radio will go there
Contest commands
Some special commands are needed for use in a contest:
- Switch between Run mode and S&P mode: +
- Confirm last serial nr: "_" (underscore)
- Confirm last call: "="
- Show list of zones yet to be worked: ":zones"
- Show list of countries left over: ":cty"
- Show propagation: "ctrl-p"
- Switch to keyboard: "," or "ctrl-k"
Keyer commands
- Change the speed with left-arrow or right-arrow. You can see the speed in the upper status line (S=45)
- Change the auto_cq delay with page-up and page-down. This only works if the call input field is empty.
If it is not, you will change the RST value. Set it to the total length of the message + the receive time.
! You can see the value in te upper status line (D=11)
- Start the auto_cq with F12. Or if contest mode is on, and input field is empty, with ENTER.
- Switch to keyboard: "," or "ctrl-k" The above commands also work when the keyboard is on.
- Change the sidetone frequency with ":tone". A value of 0 will switch sidetone off.
Radio control commands
- Don't forget to switch trxcontrol on (:trxcontrol).
- See your trx frequency on the right hand side of the screen just below the log line.
E.g. TRX: 15023.7
- Tlf will follow the bandswitch of the trx.
- Fast qsy by just entering the new qrg into the empty call input field in kHz (e.g. 3505).
- Remember your run frequency by putting it into the memory with "#". The memory display will pop up and show
the frequency you can return to by again entering "#".
- Grab a dx spot. This only works if you have a radio interface program for your type of trx running, and
if you are connected to a cluster and have the bandmap or spot window
on screen. Just enter part of the call of the dx station (e.g. 6W when the call is 6W/DJ0LN/P), enter "ctrl-g" (for "grab")
and you will see the trx magically qsy to the spot frequency, where you can loose valuable time in the
pileup. :-}
- Add a spot to the list by entering a Call into the call field and pressing Ctrl-A. This
works with band map as well as spot list.
- If you set the RIT parameter (:RIT), the RIT will be reset after a qso is logged.

Ctrl-f will give you a window in which you can change the TRX frequency in 100Hz steps (with up-arrow, down_arrow).
A Radio Control Interface is available for the tec tec 563 (OMNI VI+). This possibly also works for the ICOM 735.
If your radio is not covered, try to find somebody to knit an interface for you. The ten tec interface was quite easy to do.
The interface to tlf is simple: QRG must contain the trx frequency as an ASCII value, (e.g. 14011.5), and QRGOUT writes the
qsy frequency in the same way. (special value for ten tec 563: a value of 99 tells the trxcontrol program to reset the RIT for me.)
Log commands
- Look at the log with ":view". It starts a new shell with LESS.
- Edit the log with ":edit". It starts a new shell with JOE. Other editors on request...
- If that is not enough you can start an empty shell with "!", and grep the logfile, copy it, etc...
Change your time zone and location
Edit the ctydb.dat file, and put the data of your qth into the line representing your country. An example:
United States: 05: 08: NA: 43.00: 87.90: 5.0: K:
If you are in zone 04, change the 05: into 04:, change the 43.00 and the 87.90 into your location. and the 5.0 (time difference to GMT) at the end to 6.0
Tlf is picky with respect to the exact format of the file; make sure the stuff is in the right columns!
The score window
The score window is adapted to the contest you are in. So if the contest parameter is set to cqww, you get
a special score window for it, showing qso's per band, countries worked per band, zones worked per band and total score.
It also gives an indication of the qso's per multiplier, and the qso rate based on the last 10 qso's.
When you restart the program the score is recalculated from the log file. When a qso is deleted from the logfile the score is not
adjusted, neither is the list of counties worked updated. You can correct this by restarting the program.
The Messages
There are 14 messages. More than I can remember. Some have a special use:
- F1= CQ call (run mode) or DE CALL (S&P mode). The "DE" can be switched on or off (:demode)
- F2 = free (normally "@ DE %"
- F3 = runmode report (e.g. @ [ 14). If # is used, the serial nr can be SHORT (TT1)
- F4 = free (normally "73" or "TU")
- F5 = free (normally "@"
- F6 = free (normally "%"
- F7 = free (normally "B4"
- F8 = free e.g. "AGN"
- F9 = free e.g. "?"
- F10 = free e.g. "QRZ?"
- F11 = free e.g. "UR CL?"
- F12 = auto_cq message, e.g. "TEST PA0RCT"
- S&P TU msg = e.g. "TU [14"
- Run TU msg = e.g. "TU %"
For the messages you can use a number of special characters:
- % for YOURCALL
- @ for HISCALL
- [ for RST
- # for serial nr.
- - lower keyer speed by 1 wpm (parallel interface only !)
- + increase keyer speed by 1 wpm (e.g. " ++++++5NN------#") (parallel interface only)
The easiest way to handle the messages is to edit them in logcfg.dat. You can then keep separate logcfg.dat files
for different contests and operating situations.
You can list the messages with ":list" and change them with ":message".
Dupe checking
With the "check" command you can open a search window which will tell you:
- On what bands you worked the station, and what the exchange was
- If the station is a dupe, the color will be red and the terminal will beep.
- On what bands you worked the country already
- On what bands you worked the zone already
- In case of other multipliers, on what bands they were worked.
- If the exchange is the same for every band, it is automatically filled into the exchange field
Check partials / auto_complete
The check partials function is controlled via the logcfg.dat file with 3 parameters:
- PARTIALS - switches the check partial function on (max. 9 calls)
- USEPARTIALS - enables the auto_complete function
- MANY_CALLS - shows a large window with up to 50 calls
The check partial calls function uses a database derived from the master.dta file containing
some 25.000 known contest calls.
When the USEPARTIALS parameter is on, tlf will complete the call as soon as it is unique in the database.
This can of course lead to strange effects, but in my experience there are far more hits than misses.
Sometimes you must edit the call because it has locked on a unique call.... Try it, and switch it off when you don't like it.
Some people find that 9 calls is not enough.... MANY_CALLS will give you many calls.
Checking propagation
For the propagation check to work, the file "wwvfile" must contain a value for either SFI (solar flux)
or R (or SSN), the sunspot number. The calculation actually uses the SSN value which is derived from SFI.
If you are connected to a cluster, the WWV values will automatically be stored, and the last value used.
Clfile is periodically checked for this, and the value stored in wwvfile.
Starting with version 0.4.4 it is now possible to include the value of R or SFI in the logcfg.dat file.
The value will be picked up within a minute, and will be used for subsequent
calculations. The calculations are quite simple, but you may compare it to e.g. minprop 3. and see that it
really comes quite close. This may be enhanced in the future, to influence the multiplier map...
All timing is related to UTC. You must have your computer clock running on UTC.
DX cluster connection
Tlf regularly looks into a file called "clfile" in its working directory. It is your responsibility to get the info into it. Some examples:
- Goto the working directory and start a telnet session in a new terminal.
- start this session with telnet node | tee -a clfile
- Connect to the dxcluster, e.g. using call , minicom or a telnet client
- For filtering, bandmap etc to work, the lines in clfile have to start with: "DX de", Escape characters at the start of the line
have to be filtered out (e.g. by using "|cut -c 7-97"
Relevant commands:
- :cluster - full cluster content (filter with ":fil")
- :spots - only DX spots in order of time
- :map - only spots for this band, sorted in frequency
- Ctrl-A - add your own spot to the list (if radio interface is present)
You can filter out announcements etc. by editing the script "filterline".
Editing the .paras file
Here is an example of a .paras file. Normally, you should not have to edit it, all can be changed from
within the program.
Example of a typical .paras file (cqww contest):
# Call ----------------------------------
PA0RCT
# Messages F1...F12 ---------------------
CQ % K
@ DE %
@ ++++++[------ 14
TU
@
%
@ SRI QSO B4 GL
AGN
?
QRZ?
PSE K
TEST % %
# TU message S&P mode---------------------
TU [14
# TU message CQ mode---------------------
TU %
# Info for top status line----------------
1=CQ 2=DE 3=RST 4=73 5=HIS 6=MY 7=B4 8=AGN 9=?
# Logfile----------------
cqwwxxx.log
# Contest-----------------------
cqww
# Parameters--don't change----
SADNCNN:;U
Example of a filterline script
#!/bin/bash
egrep -i "DX de|PA0RCT|DK0WCY" clfile > cl3file
The file cl3file is a temporary file necessary for the filter to work
Making a contest qso in CQ Mode
1: Press ENTER to start the F12 message ("CQ TEST YOURCALL...") or F1
HC8N: "HC8N"
2: Type HC8N
3: Press ENTER (YOU: "HC8N 5NN14") (message is in F3)
HC8N: "TUENNAT"
4: Press ENTER (YOU: "TU YOURCALL") (message in CQ_MESSAGE)
N6TR: "K7RAT"
2: type K7RAT
3: Press ENTER
etc...
Using the keyer
the keyer is started with Ctrl-K or with "," (comma). The comma will only work when the call
input field is empty (and if trxmode is CW of course.
The following special cw characters are supported on the serial interface:
AR | + |
BT | = |
SK | < |
KN | ( |
SN | ! |
AS | & |
BK | > |
The keyboard works in word mode, enabling you to correct a word with "backspace" before it is
sent to the keyer by adding either a space or enter.. Characters like SN, SK, BK are sent immediately. Stop the keyboard with ESCAPE.
Making a contest qso in S&P Mode
1: find a station to call
2: Type HC8N to enter the call into the input field
3: Press ENTER (YOU: "YOURCALL") or F1
HC8N: "YOURCALL ENNAT"
4: Press ENTER (YOU: "TU 5NN14") (the message is in SP_MESSAGE)
HC8N: "TU HC8N"
Making a normal qso
- Switch contest mode off
- Use the check window to see if you have worked the stn. before, and
to remember his/her name :-))
- Tab into the exchange field for comments (name, qth)
- Use ; (notes) for further comments
- Reprogram the key saying SRI QSO B4 to contain the local WX.
- Use , (keyboard) to tell your story, nice and slowly...
Command Overview
Most commands start with a ":", and you need to type only the first 3 characters.
:help | Show online help |
:mode | switch trx mode (CW, SSB) |
:set | list and set parameters.
the following contests are supported:
- CQWW
- WPX
- ARRL-DX (both sides)
- PACC (both sides)
- EU SPRINT
- Other (wysiwyg mults)
- DX-pedition
- General qso
|
Up-Arrow | Increase CW speed (2wpm) | )
Down-Arrow | Decrease CW speed (2wpm) |
| |
Pg-up | If call field empty: Increase Auto_CQ delay (1 sec)
If not empty: increase RST |
Pg-down | If call field empty: Decrease Auto_CQ delay (1 sec)
If not empty: decrease RST |
| |
F12 | Start Auto_CQ |
F1-F11 | Send CW message |
| |
:tone | Set sidetone frequency (200-900 Hz) or OFF (0)
A value between 2 and 20 will add weight to the cw elements |
| |
Tab | Switch between call input and exchange fields |
+ | Toggle CQ/S&P mode |
| |
Left-Arrow | Change band if callsign field empty (enter edit mode if callsign present, leave edit mode with ENTER or ESC) |
Right-Arrow | Change band |
| |
ENTER | Smart key for contest mode
Calls cq
Calls station
Sends exchange
Logs the qso |
\ | log qso w/o CW; |
; | Insert note in log |
, ctrl-k
| Keyboard on. This works only when the call input field is empty.
use ctrl-k if it isn't. |
ESCAPE | Return to call input field
|
Ctlr-p | Propagation info |
- | Delete last qso |
@ | Edit last qso |
= | Confirm last call |
_ (underscore) | Edit last qso |
| |
# | trx qrg -> mem mem -> trx qrg |
ctrl-g | Grab a dx spot |
ctrl-a | Add a dx spot to the spot list or bandmap |
ctrl-f | Change TRX frequency with up_arrow, down_arrow (100 Hz at the time) |
| |
:view | View the log with LESS |
:edit | Edit the log with JOE (ctrl-K H = help) |
:list | List CW messages |
:message | Edit CW messages |
:set, :cfg | edit logcfg.dat configuration file |
:write | Write Cabrillo file (for selected contests: CQWW, WPX, ARRL-DX) |
! | Get a new shell |
:exit | Exit the program |
Options
:multi | Toggle SINGLE/MULTI SINGLE mode on/off (switch to off, does not do anything yet) |
:contest | Toggle contest mode on/off |
:check | dupe check window on |
:nocheck | dupe check window off |
:score | Toggle score window on/off |
| |
:cluster | Show cluster window or... |
:map | Show Band Map or... |
:spots | Show last 10 spots or... |
:cloff | No cluster info (non-assisted contest operation) |
| |
:cty | Show country multipliers per continent |
:zone | Toggle zones worked display |
:trxcontrol | toggle trxcontrol on/off (default off)
Radios supported: Ten Tec 563 and icom 735. |
:ritclear | rit reset on/off |
Logcfg.dat file
EDITOR=joe
#EDITOR=vi | choose your favourite editor for :edit and :set |
CALL=PA0RCT | don't forget to change this one !! |
#CONTEST=cqww
#CONTEST=wpx
#CONTEST=sprint
#CONTEST=arrldx_usa
#CONTEST=arrldx_dx
#CONTEST=arrl_fd
#CONTEST=pacc_pa
#CONTEST=pacc_dx
CONTEST=dxped
#CONTEST=qso
#CONTEST=other | choose your standard contest or experiment with 'other' |
LOGFILE=dxped.log | don't forget to change this one !! |
#LPT1
COM1 | choose your keyer output port |
##---speed (6 ... 60 wpm)
SPEED=30
##---weight (-5 ... 5 ms)
WEIGHT=0
##---txdelay (ms)
TXDELAY=51
##---sidetone (200...800, 0 = mute)
TONE=800
# | set the keyer parameters most (except speed and sidetone) are only
available for the parallel port keyer |
#RADIO_CONTROL
#RIT_CLEAR
#SHOW_FREQUENCY
| rig control parameters clear RIT after qso . |
#CLUSTER
#BANDMAP
SPOTLIST
FILTER
#
#SCOREWINDOW
CHECKWINDOW | switch information windows on/off |
#PARTIALS
#USEPARTIALS
#MANY_CALLS | switch partial call function on auto_complete function see many calls :-) |
#SUNSPOTS=102
SFI=180 | set initial value for muf calculation |
F1=CQ CQ DX DE % % k
F2=@ DE %
F3=@ [
F4=TU 73
F5= @
F6=%
F7=@ SRI QSO B4 GL
F8=AGN
F9= ?
F10= QRZ?
F11= PSE K
F12=TEST % %
#
CW_TU_MSG=TU 73 %
S&P_TU_MSG=TU [
#
#SHORT_SERIAL
LONG_SERIAL
#
SEND_DE |
% = call
@ = hiscall
# = serial
[ = RST
+ = increase cw speed
- = decrease cw speed
(works only with parport
interface)
F12: auto_cq message
contest mode: TU message in CQ mode
contest mode: TU message in S&P mode
e.g. TT1 instead of 001
relict from TRlog |
#RECALL_MULTS | used in "other" contest mode when exchange does not change between bands |
#ONE_POINT
#THREE_POINTS
| used in "other" contest mode, points per qso for scoring |
#WYSIWYG_MULTIBAND | mult used in "other" contest mode, counts per band |
#WYSIWYG_ONCE | mult used in "other" contest mode, counts once per contest |
#POWERMULT_5
#POWERMULT_2
#POWERMULT_1
| power multiplier for qrp contests or e.g. the arrl field day the qso points are multiplied
by this fixed amount, depending on output power |
# MULTIPLIER LIST #
| for future use (excluded countries, list of districts, provinces etc. etc...) |
BUGS/TODO
If you find any, or have suggestions for TLF, send comment to
PA0RCT@AMSAT.ORG
Licence and copyright
Copyright 2001, 2002 Rein Couperus (PA0RCT)
This program is distributed under the terms of the GNU General Public License.
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA